Cameron Katri's Manual Page Server

NAME

ifconfig — configure network interface parameters

SYNOPSIS

DESCRIPTION

The ifconfig utility is used to assign an address to a network interface and/or configure network interface parameters.

The following options are available:

address

For the DARPA-Internet family, the address is either a host name present in the host name data base, hosts(5), or a DARPA Internet address expressed in the Internet standard “dot notation”.

It is also possible to use the CIDR notation (also known as the slash notation) to include the netmask. That is, one can specify an address like 192.168.0.1/16.

For the “inet6” family, it is also possible to specify the prefix length using the slash notation, like ::1/128. See the prefixlen parameter below for more information.

The link-level (“link”) address is specified as a series of colon-separated hex digits. This can be used to e.g. set a new MAC address on an ethernet interface, though the mechanism used is not ethernet-specific. If the interface is already up when this option is used, it will be briefly brought down and then brought back up again in order to ensure that the receive filter in the underlying ethernet hardware is properly reprogrammed.

address_family

Specify the address family which affects interpretation of the remaining parameters. Since an interface can receive transmissions in differing protocols with different naming schemes, specifying the address family is recommended. The address or protocol families currently supported are “inet”, “inet6”, and “link”. The default is “inet”. “ether” and “lladdr” are synonyms for “link”.

dest_address

Specify the address of the correspondent on the other end of a point to point link.

interface

This parameter is a string of the form “name unit”, for example, “en0”.

The following parameters may be set with ifconfig:

add

Another name for the alias parameter. Introduced for compatibility with BSD/OS.

alias

Establish an additional network address for this interface. This is sometimes useful when changing network numbers, and one wishes to accept packets addressed to the old interface. If the address is on the same subnet as the first network address for this interface, a non-conflicting netmask must be given. Usually 0xffffffff is most appropriate.

-alias

Remove the network address specified. This would be used if you incorrectly specified an alias, or it was no longer needed. If you have incorrectly set an NS address having the side effect of specifying the host portion, removing all NS addresses will allow you to respecify the host portion.

anycast

(Inet6 only.) Specify that the address configured is an anycast address. Based on the current specification, only routers may configure anycast addresses. Anycast address will not be used as source address of any of outgoing IPv6 packets.

arp

Enable the use of the Address Resolution Protocol (arp(4)) in mapping between network level addresses and link level addresses (default). This is currently implemented for mapping between DARPA Internet addresses and IEEE 802 48-bit MAC addresses (Ethernet, FDDI, and Token Ring addresses).

-arp

Disable the use of the Address Resolution Protocol (arp(4)).

broadcast

(Inet only.) Specify the address to use to represent broadcasts to the network. The default broadcast address is the address with a host part of all 1's.

debug

Enable driver dependent debugging code; usually, this turns on extra console error logging.

-debug

Disable driver dependent debugging code.

delete

Another name for the -alias parameter.

down

Mark an interface “down”. When an interface is marked “down”, the system will not attempt to transmit messages through that interface. If possible, the interface will be reset to disable reception as well.

ether

Another name for the lladdr parameter.

lladdr addr

Set the link-level address on an interface. This can be used to e.g. set a new MAC address on an ethernet interface, though the mechanism used is not ethernet-specific. The address addr is specified as a series of colon-separated hex digits. If the interface is already up when this option is used, it will be briefly brought down and then brought back up again in order to ensure that the receive filter in the underlying ethernet hardware is properly reprogrammed.

media type

If the driver supports the media selection system, set the media type of the interface to type. Some interfaces support the mutually exclusive use of one of several different physical media connectors. For example, a 10Mbit/s Ethernet interface might support the use of either AUI or twisted pair connectors. Setting the media type to 10base5/AUI would change the currently active connector to the AUI port. Setting it to 10baseT/UTP would activate twisted pair. Refer to the interfaces' driver specific documentation or man page for a complete list of the available types.

mediaopt opts

If the driver supports the media selection system, set the specified media options on the interface. The opts argument is a comma delimited list of options to apply to the interface. Refer to the interfaces' driver specific man page for a complete list of available options.

-mediaopt opts

If the driver supports the media selection system, disable the specified media options on the interface.

rxcsum, txcsum

If the driver supports user-configurable checksum offloading, enable receive (or transmit) checksum offloading on the interface. Some drivers may not be able to enable these flags independently of each other, so setting one may also set the other. The driver will offload as much checksum work as it can reliably support, the exact level of offloading varies between drivers.

-rxcsum, -txcsum

If the driver supports user-configurable checksum offloading, disable receive (or transmit) checksum offloading on the interface. These settings may not always be independent of each other.

tso

If the driver supports tcp(4) segmentation offloading, enable TSO on the interface. Some drivers may not be able to support TSO for ip(4) and ip6(4) packets, so they may enable only one of them.

-tso

If the driver supports tcp(4) segmentation offloading, disable TSO on the interface. It will always disable TSO for ip(4) and ip6(4).

lro

If the driver supports tcp(4) large receive offloading, enable LRO on the interface.

-lro

If the driver supports tcp(4) large receive offloading, disable LRO on the interface.

av

If supported by the driver, enable 802.1 AVB on the interface.

-av

If supported by the driver, disable 802.1 AVB on the interface.

vlanmtu, vlanhwtag

If the driver offers user-configurable VLAN support, enable reception of extended frames or tag processing in hardware, respectively. Note that this must be issued on a physical interface associated with vlan(4), not on a vlan(4) interface itself.

-vlanmtu, -vlanhwtag

If the driver offers user-configurable VLAN support, disable reception of extended frames or tag processing in hardware, respectively.

create

Create the specified network pseudo-device. If the interface is given without a unit number, try to create a new device with an arbitrary unit number. If creation of an arbitrary device is successful, the new device name is printed to standard output unless the interface is renamed or destroyed in the same ifconfig invocation.

destroy

Destroy the specified network pseudo-device.

plumb

Another name for the create parameter. Included for Solaris compatibility.

unplumb

Another name for the destroy parameter. Included for Solaris compatibility.

metric n

Set the routing metric of the interface to n, default 0. The routing metric is used by the routing protocol (routed(8)). Higher metrics have the effect of making a route less favorable; metrics are counted as additional hops to the destination network or host.

mtu n

Set the maximum transmission unit of the interface to n, default is interface specific. The MTU is used to limit the size of packets that are transmitted on an interface. Not all interfaces support setting the MTU, and some interfaces have range restrictions.

netmask mask

(Inet only.) Specify how much of the address to reserve for subdividing networks into sub-networks. The mask includes the network part of the local address and the subnet part, which is taken from the host field of the address. The mask can be specified as a single hexadecimal number with a leading ‘0x’, with a dot-notation Internet address, or with a pseudo-network name listed in the network table networks(5). The mask contains 1's for the bit positions in the 32-bit address which are to be used for the network and subnet parts, and 0's for the host part. The mask should contain at least the standard network portion, and the subnet field should be contiguous with the network portion.

The netmask can also be specified in CIDR notation after the address. See the address option above for more information.

prefixlen len

(Inet6 only.) Specify that len bits are reserved for subdividing networks into sub-networks. The len must be integer, and for syntactical reason it must be between 0 to 128. It is almost always 64 under the current IPv6 assignment rule. If the parameter is omitted, 64 is used.

The prefix can also be specified using the slash notation after the address. See the address option above for more information.

remove

Another name for the -alias parameter. Introduced for compatibility with BSD/OS.

link[0-2]

Enable special processing of the link level of the interface. These three options are interface specific in actual effect, however, they are in general used to select special modes of operation. An example of this is to enable SLIP compression, or to select the connector type for some Ethernet cards. Refer to the man page for the specific driver for more information.

-link[0-2]

Disable special processing at the link level with the specified interface.

up

Mark an interface “up”. This may be used to enable an interface after an “ifconfig down”. It happens automatically when setting the first address on an interface. If the interface was reset when previously marked down, the hardware will be re-initialized.

The following parameters are for ICMPv6 Neighbor Discovery Protocol. Note that the address family keyword “inet6” is needed for them:

nud

Perform network unreachability detection (NUD).

-nud

Do not perform network unreachability detection (NUD).

ifdisabled

Disable all IPv6 communication on the interface.

-ifdisabled

Do not disable all IPv6 communication on the interface.

insecure

Disable the processing of Secure Neighbor Discovery (SEND).

-insecure

Do not disabled the processing of Secure Neighbor Discovery (SEND).

dad

Perform duplicate address detection (DAD).

-dad

Do not perform duplicate address detection (DAD).

replicated

Modify duplicate address detection (DAD) protocol to expect that interface configuration is replicated at a network sleep proxy. Ignores certain NA messages and disables optimistic DAD.

-replicated

Do not use modified duplicated address detection (DAD) protocol.

The following parameters are specific to link aggregate interfaces:

bonddev iface

If the interface is a bond pseudo device, associate physical interface iface with it. By default, the bond pseudo device is in LACP (Link Aggregation Control Protocol) mode (see bondmode below). In this mode, the device conforms to the IEEE 802.3ad Link Aggregation specification.

If this is the first physical interface to be associated with the bond interface, the bond interface inherits the ethernet address from the physical interface. Physical interfaces that are added to the bond have their ethernet address re-programmed so that all members of the bond have the same ethernet address. If the physical interface is subsequently removed from the bond using -bonddev, a new ethernet address is chosen from the remaining interfaces, and all interfaces are re-programmed again with the new ethernet address. If no remaining interfaces exist, the bond interface's ethernet address is cleared.

If the specified physical interface iface is not capable of having its ethernet address re-programmed, the bonddev command will fail.

Once the physical interface iface is successfully associated with the bond interface, all received packets are diverted to the bond interface. The physical interface is no longer useable on its own, and remains that way until it is removed from the bond using -bonddev.

It is possible that the specified interface iface is not capable of aggregating, and may remain unused until the operating conditions change.

The link status of the bond interface depends on the state of link aggregation. If no active partner is detected, the link status will remain inactive.

To monitor the 802.3ad Link Aggregation state, use the -b option.

A physical interface that is associated with a vlan pseudo device cannot at the same time be associated with a bond pseudo device. A physical interface cannot be associated with more than one bond pseudo device at the same time.

It is not possible to associate a bond with pseudo interfaces such as vlan. Only physical ethernet interfaces may be associated with a bond.

-bonddev iface

If the interface is a bond pseudo device, disassociate the physical interface iface from it. Before the interface is removed from the bond, the bond device announces to the link partner that the interface is now individual and no longer aggregatable. If the physical iface is the last interface in the bond, the bond interface clears its link address.

bondmode lacp | static

If the interface is a bond pseudo device, this option will set the mode on the bond interface. The two currently supported modes are lacp and static. The default mode is lacp.

To enable static mode (and turn off LACP), specify static. In static mode, a member interface is made an active part of the link aggregate as long as the link status is active.

To re-enable LACP mode, specify lacp.

The following parameters are specific to IP tunnel interfaces, gif(4):

tunnel src_addr dest_addr

Configure the physical source and destination address for IP tunnel interfaces. The arguments src_addr and dest_addr are interpreted as the outer source/destination for the encapsulating IPv4/IPv6 header.

-tunnel

Unconfigure the physical source and destination address for IP tunnel interfaces previously configured with tunnel.

deletetunnel

Another name for the -tunnel parameter.

The following parameters are specific to bridge interfaces:

addm interface

Add the interface named by interface as a member of the bridge. The interface is put into promiscuous mode so that it can receive every packet sent on the network.

deletem interface

Remove the interface named by interface from the bridge. Promiscuous mode is disabled on the interface when it is removed from the bridge.

maxaddr size

Set the size of the bridge address cache to size. The default is 100 entries.

timeout seconds

Set the timeout of address cache entries to seconds seconds. If seconds is zero, then address cache entries will not be expired. The default is 240 seconds.

addr

Display the addresses that have been learned by the bridge.

static interface-name address

Add a static entry into the address cache pointing to interface-name. Static entries are never aged out of the cache or re-placed, even if the address is seen on a different interface.

deladdr address

Delete address from the address cache.

flush

Delete all dynamically-learned addresses from the address cache.

flushall

Delete all addresses, including static addresses, from the address cache.

discover interface

Mark an interface as a “discovering” interface. When the bridge has no address cache entry (either dynamic or static) for the destination address of a packet, the bridge will forward the packet to all member interfaces marked as “discovering”. This is the default for all interfaces added to a bridge.

-discover interface

Clear the “discovering” attribute on a member interface. For packets without the “discovering” attribute, the only packets forwarded on the interface are broadcast or multicast packets and packets for which the destination address is known to be on the interface's segment.

learn interface

Mark an interface as a “learning” interface. When a packet arrives on such an interface, the source address of the packet is entered into the address cache as being a destination address on the interface's segment. This is the default for all interfaces added to a bridge.

-learn interface

Clear the “learning” attribute on a member interface.

stp interface

Enable Spanning Tree protocol on interface. The if_bridge(4) driver has support for the IEEE 802.1D Spanning Tree protocol (STP). Spanning Tree is used to detect and remove loops in a network topology.

-stp interface

Disable Spanning Tree protocol on interface. This is the default for all interfaces added to a bridge.

maxage seconds

Set the time that a Spanning Tree protocol configuration is valid. The default is 20 seconds. The minimum is 6 seconds and the maximum is 40 seconds.

fwddelay seconds

Set the time that must pass before an interface begins forwarding packets when Spanning Tree is enabled. The default is 15 seconds. The minimum is 4 seconds and the maximum is 30 seconds.

hellotime seconds

Set the time between broadcasting of Spanning Tree protocol configuration messages. The hello time may only be changed when operating in legacy stp mode. The default is 2 seconds. The minimum is 1 second and the maximum is 2 seconds.

priority value

Set the bridge priority for Spanning Tree. The default is 32768. The minimum is 0 and the maximum is 61440.

ifpriority interface value

Set the Spanning Tree priority of interface to value. The default is 128. The minimum is 0 and the maximum is 240.

ifpathcost interface value

Set the Spanning Tree path cost of interface to value. The default is calculated from the link speed. To change a previously selected path cost back to automatic, set the cost to 0. The minimum is 1 and the maximum is 200000000.

ifmaxaddr interface size

Set the maximum number of hosts allowed from an interface, packets with unknown source addresses are dropped until an existing host cache entry expires or is removed. Set to 0 to disable.

hostfilter interface address

Configure the bridge to accept incoming packet on the interface only if they match the given MAC address and IP address -- use the command twice to set both type of addresses. Other filtering restrictions apply.

-hostfilter interface

Allow traffic from any host on that interface.

The following parameters are specific to vlan interfaces:

vlan vlan_tag

Set the VLAN tag value to vlan_tag. This value is a 16-bit number which is used to create an 802.1Q VLAN header for packets sent from the vlan(4) interface. Note that vlan and vlandev must both be set at the same time.

vlandev iface

Associate the physical interface iface with a vlan(4) interface. Packets transmitted through the vlan(4) interface will be diverted to the specified physical interface iface with 802.1Q VLAN encapsulation. Packets with 802.1Q encapsulation received by the parent interface with the correct VLAN tag will be diverted to the associated vlan(4) pseudo-interface. The vlan(4) interface is assigned a copy of the parent interface's flags and the parent's ethernet address. The vlandev and vlan must both be set at the same time. If the vlan(4) interface already has a physical interface associated with it, this command will fail. To change the association to another physical interface, the existing association must be cleared first.

Note: if the hardware tagging capability is set on the parent interface, the vlan(4) pseudo interface's behavior changes: the vlan(4) interface recognizes that the parent interface supports insertion and extraction of VLAN tags on its own (usually in firmware) and that it should pass packets to and from the parent unaltered.

-vlandev [iface]

If the driver is a vlan(4) pseudo device, disassociate the parent interface from it. This breaks the link between the vlan(4) interface and its parent, clears its VLAN tag, flags and its link address and shuts the interface down. The iface argument is useless and hence deprecated.

The ifconfig utility displays the current configuration for a network interface when no optional parameters are supplied. If a protocol family is specified, ifconfig will report only the details specific to that protocol family.

If the -m flag is passed before an interface name, ifconfig will display the capability list and all of the supported media for the specified interface.

If -L flag is supplied, address lifetime is displayed for IPv6 addresses, as time offset string.

Optionally, the -a flag may be used instead of an interface name. This flag instructs ifconfig to display information about all interfaces in the system. The -d flag limits this to interfaces that are down, and -u limits this to interfaces that are up. When no arguments are given, -a is implied.

The -l flag may be used to list all available interfaces on the system, with no other additional information. Use of this flag is mutually exclusive with all other flags and commands, except for -d (only list interfaces that are down) and -u (only list interfaces that are up).

The -v flag may be used to get more verbose status for an interface.

The -C flag may be used to list all of the interface cloners available on the system, with no additional information. Use of this flag is mutually exclusive with all other flags and commands.

The -r flag may be used to show additional information related to the count of route references on the network interface.

For bridge interfaces, the list of addresses learned by the bridge is not shown when displaying information about all interfaces except when the -v flag is used.

The -X flag may be used to list interfaces whose names match the regular expression in the pattern. See re_format(7) for more information on regular expressions. This flag may be used with the -a flag and the -l flag to further restrict the set of interfaces to be listed.

Only the super-user may modify the configuration of a network interface.

NOTES

The media selection system is relatively new and only some drivers support it (or have need for it).

EXAMPLES

Assign the IPv4 address 192.0.2.10, with a network mask of 255.255.255.0, to the interface en0:

Add the IPv4 address 192.0.2.45, with the CIDR network prefix /28, to the interface en0, using add as a synonym for the canonical form of the option alias:

Remove the IPv4 address 192.0.2.45 from the interface en0:

Add the IPv6 address 2001:DB8:DBDB::123/48 to the interface en0:

Remove the IPv6 address added in the above example, using the / character as shorthand for the network prefix, and using delete as a synonym for the canonical form of the option -alias:

Configure the interface en1, to use 100baseTX, full duplex Ethernet media options:

Create the software network interface gif1:

Destroy the software network interface gif1:

DIAGNOSTICS

Messages indicating the specified interface does not exist, the requested address is unknown, or the user is not privileged and tried to alter an interface's configuration.

SEE ALSO

netstat(1), netintro(4), sysctl(8)

HISTORY

The ifconfig utility appeared in 4.2BSD.

BUGS

Basic IPv6 node operation requires a link-local address on each interface configured for IPv6. Normally, such an address is automatically configured by the kernel on each interface added to the system; this behaviour may be disabled by setting the sysctl MIB variable net.inet6.ip6.auto_linklocal to 0.

If you delete such an address using ifconfig, the kernel may act very odd. Do this at your own risk.